|
The final thing to do for the woodpecker is getting him some legs, and particularly some feet, to hang onto the log with. Downey woodpeckers crouch so close to a tree when pecking into it not much can really be seen of their undercarriage. I decided to make his feet a little exaggerated just to make him a little more interesting.
In the final fit up I will epoxy his feet to the outer layer of bark and to the pivot post which will be glued into the log. The bark remains a little flaky even after a few layers of urethane have been applied to try to stick it all together, so will assemble the feet and pivot post with epoxy - just to be sure. The critical fitting will be to ensure that the woodpecker is not mounted too close to his feet so that his belly prevents unrestricted rocking motion. Once I have created the "hole" that the woodpecker is working on I will check full range of motion again with beak down to its lowest position. In the end I will likely assemble the feet and pivot post together apart from the log so I can ensure this clearance is good, and then glue the post and feet down with epoxy under the feet, and carpenters glue on the pivot post to body joint. Here is a photo of the position of the feet with the woodpecker removed, prior to painting. You can see the passages for the control like to come from below. One claw was shaved a little to avoid conflict with the control arm movement. The second photo is a profile view with the woodpecker in place so you can see the clearance left for rocking. the pivot post has not been painted yet in this photo.
0 Comments
I've been working on my nameless woodpecker for "Carpenter Ants". I haven't named him yet. "Woody" seems just a little to obvious to me. I'll have to keep thinking. If you have a suggestion , send me a note! The woodpecker has got some paint now as you can see below, as I said before, nothing too spectacular, but enough to be recognizable. Here he is pictured below poised on the top of the log while I try to locate his exact position. The first challenge is that he sits far enough to the right on the log so the drilled passages for his motion linkages do not penetrate the hollow centre of the long. The first step I took was to locate the mounting post where he will pivot in his rocking motion. In the picture of the log you can see the post I made which is cut down into the bark to the hardwood layer. There is a 1/4" dowel in this post that reaches down in the hardwood layer for strength. The post will not be glued into place until much later so I can easily design and attach his legs; which will help hide the post itself and also facilitate using a temporary drilling cradle so I can drill holes prependicular to the bottom the log on my drill press. (That being done upside down of course!) Next steps were to drill two holes to provide access for the motion links. If you look closely in the pictures above or in the frozen Fram of the video below you will see to temporary link rods. The thin wire on the far right controls the rocking motion of the woopleckner, and the thicker one between the post and thin control rod id=s. the one that turns his head. These rods extend down two separate 3/8" holes and emerge into the main mechanism area that will below the long when completed. Keep in mind that the woodpecker and it controls links will likely be the last components I will assemble on this automata. just to keep him out of harms way. Here is a 50 second video that shows the range of motion I expect to employ with the woodpecker. He should peck on the log, pause, listen for noises in the log, and look around, the sequence of which has not been exactly determined. Things are a little jerky in that I am reaching down under the log and tugging on the link rods with my fingers, It will be better! There is a brief section of dialogue on the last half of the video where I repeat some things, unrehearsed of course! I think I'll go directly to making his legs and tuning the control motions and clearances next. Oh, I almost forgot to add I will make a little dent in the top of the log so it looks like he has made some progress pecking. Al Sometimes when you're making automata you will find you want to put unseen mechanism components inside characters rather than have their movement controlled by external visible wires and rods. For many viewers, this adds a little more fascination to our automata creations. I try to do this often. There is a trade-off of course, in that, sometimes you have to exaggerate the look of a character in order to fit the mechanism inside. Such as the case in my current project called “Carpenter Ants”, which I spoke of in my previous website blog. This project has a Downy woodpecker that's pecking on the top of a log disturbing the activity of the carpenter ants inside. I chose to try to hide key parts of the mechanism in the body of the bird itself. No award winning realistic bird craving trophy on this one! Oh well. Here is how I did it. The body of the woodpecker is made using three 1/2” thick basswood blocks, each one with an identical exterior profile. The centre block will house the head shaft and control link as well as the attachment point for the link arm that tips the woodpecker forward and back. The body block on the left side will be hollowed out to allow room for movement of the control arms which need to provide 90 degrees of rotation for the head. Each block is drilled with three critical holes needed to index the pieces together during assembly. A 1/4” diameter hole at the top front will ensure alignment of the front ends with a dowel pushed in. A 1/8” diameter hole near the rear is where a rod will be inserted to attach a link to pull the bird up and down. During the assembly stages I will also insert a brass rod to keep things aligned. The third hole is a 3/16” hole for the pin that will become the centre of rotation for the woodpecker at his feet. Let’s look at the centre block first. The shaft that will turn the head cannot be installed unless the block is cut to allow insertion and proper alignment. This mechanism will have bearing recessed into each end of the block and retaining collars to hold them in place. The shaft has a short brass link arm soldered on the rear end. The the other end of the arm has a swivel joint attached. The swivel joint will allow the connection rod for the head turning to remain in the vertical plane even as the woodpecker tips up and down. This will reduce potential binding, smoothen movement, and make cam design a little easier. (For those interested this swivel is a Du-Bro 2139 Swivel Ball Link for 4-40 Rods available at most hobby shops. 4-40 is a standard American screw size indicating a #4 screw diameter with 40 threads per inch. ) They are frequently used in model airplane and car controls.) The added benefit for this application is that the rod control connection at the woodpecker end is a 4-40 female thread sleeve. A long, rigid, 18” long control rod will be able to be installed easily below the log even after the woodpecker is installed. Lets see what the three pieces look like before gluing them together. Next it is on to dry fit the blocks, check for enough clearance on the internal parts, take the paper off the sides, apply some glue, clamp them together and go have a congratulatory coffee! Moving on the next step is to cut out and drill the wings, but do not drill the 1/4” holes all the way through, only 1/4” deep. I do some shaping before attaching the wings to the body, just because it is easer. I also shape the neck area of the body at this time. After a dry fit, glue the wings on and sand the entire assembly smooth. I then decided to do a little pyrography just to give the body some feather detail, but but far from enough to win that carvers prize! In one of these photos you can see the 3/16” hole on the wing where to pivot pin will be installed and if you look closely you can see the 1/8” hole for the rear tipping pin. Both of these will be plugged after a metal pin is inserted connect a link and finished to match the outside of the wing as on of the last assembly activities. I will have to turn the log upside down several times to complete the rest of the project so the woodpecker will likely be one of the last pieces attached. Some of you may think this is a little overkill. Yes I have made this configuration before without bearings, bushings, and swivels but never for a bird that would hit hard with its beak like this one hopefully will. And heaven forbid if is stiff in the end. I just am being cautious here. For a little extra effort and a few bucks I will sleep more soundly, this is unless the pecking noise rings in my ear at night. Head showing weights installed Although there is no active mechanism in the head I will mention a few important hidden features. First off, there is a larger shallow hole that allows the head to slide down and cover the protruding shaft bushing. This will also provide additional glue contact surface beyond that of the protruding 3/32” shaft. To help the beak to end up looking down when at rest there is a 1/8” diameter steel rod weight installed below the centre line of the head to get a little gravity assist! Also there is a brass rod inserted the full length of the beak as a assist, but really is meant to give a hard surface so you will hear a pecking noise when I add an additional small plate go the surface of the log where the beak strikes. I though wood alone may be too destructive and to quiet. I’ve added a photo so you can see them both. Well ,that’s enough for now. Next I will be painting Mr. Woodpecker and making his pivot attachment and legs. That should definite the hole locations for drilling down through the solid part of the log for the linkage rods. Blog ya later! Often when I am making automata pieces I run into a situation where I can either take the simplest path, or spend some extra effort to make something that seems more authentic. I found myself facing this decision on my latest automata project I currently call “Carpenter Ants” I am putting a Downey woodpecker on the top of a real cedar log that has a hollow centre that will be populated with carpenter ants. I wanted any control links for the woodpecker to be hidden as much as possible, so I decided to drill holes down through the solid part of the log. I had made a bird for a project in the past that had movements similar to what I thought might work well and set out to make a little prototype of a potential woodpecker in action. I thought the woodpecker should tap on the log loudly, which would stop all activity in the ant colony, and then he would listen for any more noise before deciding what he should do next. Of course having a neat, simple control scheme would be desirable because of the close quarters I was going to be working in with using a hollow log as a platform. Here’s a photo of my simple prototype I made to capture a “pecking” and “listening” mode into into one control link. Here is how it works. If you only pull the wire hanging down on the tail if the woodpecker a little , he simply pulls his body straight up, without turning his head. Push the wire back up and his body lowers and his heads goes straight down to the log again. Repeated ups and downs will generate a pecking motion. Objective #1 of the motion is achieved! Now lets something that might suggest listening. If you pull the control link down farther the woodpeckers body will rise further and his head will turn to his left and will hold that position, perhaps as if listening for any insect noises as woodpeckers might do. you can then lower body and his head will straighten out and he can return to pecking. The next photo shows the prototype in a more vertical position. So we are now at the crux of the simplicity versus authenticity issue! Woodpeckers do not stand up and turn their heads listen for noises in a tree trunk, they turn their heads and crouch close to the tree trunk to listen. This design maybe be simple but it may not seem authentic to the viewer. I do admit it could be very engaging or “cute” to the observer, which is always a great component of automata design, to have the woodpecker look directly out at them but it wasn’t what I was striving for this particular portion of the project.
The solution of course is to have two linkages, one to control the body movement, and one to control the head position. With two control systems there are an infinite number of motions that could be achieved, including one where after the woodpecker pecks he raises his body, turns his head and lowers his body again, head still turned, to appear as if he was really trying hard to listen closely. This is a much more authentic representation of what the bird actually does and it give a clearer picture for the viewer to recognize the action taking place. That all that said, with this decision the design of the two separate control mechanisms and synchronization of their codependent motions requires some additional work! But I think in this case it is worth it. Next post will be how I solved this dilemma mechanically. Al |
Why Automata?Automata is a creative blend of my life interests , engineering, art and woodworking. Archives
October 2026
Categories
All
|

RSS Feed